Spraytecs Air Atomizers are a family of products suitable for all industry processes where special performances are mandatory.
Here below are shown models and accessories, where liquids can be supplied through a siphone feeding (gravity) or by pressure.
Contact us for any question or special requirement.
EXTREME LOW FLOW - COMPACT - SIPHON FEED
This innovative AA series Compact Air Atomizer full cone spray jet is suitable for applications, where extremely low liquid flow rate is imperative and very small drops are needed.
The above shown Compact AA series Spraytecs Air Atomizer reach an unbelievable low flow rate, the lowest liquid flow rate of the market, with the value of only 0.007 lph at 0.3 bar!
Liquid is supplied by siphone fed.
Liquid Inlet is 1/8" BSP female and 1/4" BSP male. Air Inlet is M5, female.
This small AA series Compact Air Atomizer full cone spray jet is suitable for applications, where very low liquid flow rate is important and very small drops are needed.
The above shown Compact AA series Spraytecs Air Atomizer reach an incredibly low flow rate, with the value of only 0.024 lph at 0.3 bar!
Liquid is supplied by siphone fed.
Liquid Inlet is 1/8" BSP and Air Inlet is M5, female.
LOW FLOW - SIPHON FEED
This AA series Air Atomizer full cone spray jet is suitable for many applications, where low liquid flow rate is imperative and very small drops are needed.
The above shown AA series Spraytecs Air Atomizer has a low liquid flow rate, with the value of only 0.13 lph at 1 bar.
Liquid is supplied by siphone fed.
Liquid Inlet and Air Inlet are 1/4" BSP, female.
The internal atomizer design is smart, and the formation of big drops leakage does not happen, also when the spray service is stopped after a process cycle.
AA14C0013T1
AA14C0013B1
AA14C0013B4
LOW FLOW COMPACT - SIPHON FEED
This innovative Compact AA series Air Atomizer full cone spray jet is suitable for many applications, where very low liquid flow rate is imperative and very small drops are needed.
The small dimensions permits a wide range of solutions to install these atomizers in small spaces.
The above shown AA series Spraytecs Air Atomizer has a flow rate of only 0.24 lph at 1 bar.
Liquid is supplied by siphone fed.
Liquid Inlet and Air Inlet are M5, female.
Through Spraytecs thread adaptors, it is possible fit AA series Compact Air Atomizers with 1/8" BSP and 1/4" BSP threads; see details in the install accessories section.
The internal atomizer design is smart, and the formation of big drops leakage does not happen, also when the spray service is stopped after a process cycle.
MEDIUM FLOW RATE - PRESSURE FEED
With flexible performances, varying liquid and air inlets pressure, the AA series AA14B 0114 Air Atomizer full cone spray jet is suitable for many contexts, where a very accurate range of different liquid flow rates must be obtained, for different conditions and very small drops are needed.
The above shown AA series Spraytecs Air Atomizer has liquid flow rates as shown in the here below table.
Liquid Inlet and Air Inlet are 1/4" BSP, female.
HIGH FLOW RATE - PRESSURE FEED
The AA series AA14C129 Air Atomizer full cone spray jet is suitable for rough industrial contexts, where a wide range of large liquid flow rates must be obtained, for different conditions and small drops are needed.
Spraytecs AA14C129 introduce in the industry atomizers market new features, unusual in the same spray device:
- very compact size
- feed paired inlets on the rear
- different inlet threads 1/8" and 1/4" for air and liquid
- threaded outlet M16 (available in other threads on request)
- ready to be installed in a spray array configuration, made of many atomizers
The above shown AA series Spraytecs Air Atomizer has liquid flow rates as shown in the here below table.
Liquid Inlet and Air Inlet are 1/4" BSP and 1/8" BSP each, female.
Outlet is M16 x2, or M16 x1.5, or any other size on request (ask us for details).
AA14C129FT1 outlet is M16 x2, or M16 x1.5, or any other size on request (ask us for details, to check if it is possible).
The quick pipe adapters with male thread 1/4" and 1/8" are available as accessories, with other parts for your tests and application tuning.
Ask us for details!
Moreover for an easy installation of the AA series Compact Air Atomizers, Spraytecs has designed a complete line of thread adaptors, compact manifolds and brackets for the best installation in your industry application.
The brackets are compact, can be positioned in-line on a suitable rail and have built-in thread adaptors with various inlets for threads 1/4" BSP male and female, 1/8" BSP male and female, M5 female.
The Rails are suitable for quick positioning and adjusting of one or many atomizer brackets. Compatible bolts and nuts are in M6 size.
Rails must be ordered in meters of linear length.
We can accept orders also for small quantities.
Please contact us to obtain an offer about your next Spraytecs engineered spray device.
Moreover:
Check with SPRAYTECS for critical dimension, pressure, capacity, fluids in your applications, in order to receive support in your decision.
Nozzle materials must meet correctly chemical composition of fluids in your processes, always remember it.
Spray angle performance varies with pressure. Contact SPRAYTECS for specific data on your critical applications.
